Zipato RGBW Bulb 2 Z-Wave Plus Ledlamp


Zipato rgbw Bulb 2

Past in elke E27 fitting, Z-Wave plus lichtopbrengst van 806 lumen met 9Watt Stroomverbruik.
Ledlamp van Zipato type 2, volledig RGBW met aparte witte leds voor warm wit en koud wit licht.

Ean:     3858890733464

Gratis verzending vanaf 2 stuks

Op voorraad

Artikelnummer: ZIPERGBW2 Categorieën: , , ,


Zipato RGBW Bulb 2

De Zipato rgbw Bulb 2 brengt kleur in je leven.
Deze rgbw LED lamp past in elke E27 fitting en kan worden aangesloten op een Z-Wave huisautomatisering netwerk direct na het indraaien van de RGB Ledlamp.
De Z-wave chip is geïntegreerd in de behuizing van de lamp en is hierdoor draadloos aan te sturen.
Met de afstandsbediening, smartphone of tablet kunt u de helderheid en de lichtkleur aanpassen en variatie hierin aanbrengen.
Kies voor daglicht, kaarslicht of feeststemming, vanaf nu kunt u elke lichte sfeer aanpassen aan uw wensen.
Of  maak gebruik van scènes, en laat bijvoorbeeld de lichtkleur zich aanpassen wanneer het alarm geactiveerd wordt.

De Zipato rgbw Bulb 2 heeft ingebouwde kleuren bestaande uit: warm wit, koud wit en kleur LED’s.
Vanaf nu pas je de kleur aan de sfeer die u wenst maak keuze uit vele kleuren of  Er Met, kunt u maakt op sfeer gemäß om u te wensen – met gekleurd en wit licht.
De slimme lamp vervangt een 60W conventionele gloeilamp, maar verbruikt veel minder energie, slechts 9 Watt.

Zipato rgbw bulb 2 is de vernieuwde led lamp en is iets boller en kleiner dan de eerste uitgebrachte rgbw lamp van Zipato.


Lamp met E27 fitting
Geïntegreerde Z-wave Chip
Kleuren: 4-kanaals RGBW met 16 miljoen kleuren, warm wit en koud wit
Lichtopbrengst: 806 lumen
Stroomverbruik: maximaal 9 Watt
Energie-efficiënte klasse: A+
Draadloze technologie: Z-Wave Plus
Afmetingen: 120x60x60 mm



This is a secure Bulb for Europe. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
– Toggle the wall-switch, from OFF, then to ON.
– The bulb will flash once when it has been included into the network

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section. (For more information about frequency regulations please refer to the frequency coverage overview at Sigma Designs Website ).


Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Zipato Bulb 2 has 5 color channels available for you to adjust: RED, GREEN, BLUE, WARM WHITE and COLD WHITE.
Zipato Bulb 2 can be used to add color to your home or just to lighten it up in any white color tone you desire. By using Zipatile or Zipabox (or other Z-Wave) home controller, you can control the bulb from anywhere in the world, by using any smartphone (iOS or Android). Also, you can automatically set colors of your Zipato Bulb 2 to indicate events using the Zipato rule creator.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

To manually reset the bulb switch it on and off 6 times for intervals of 0,5 to 2 seconds. After the 6th time, the bulb will flash twice indicating that it?s succesfully reset.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.


1. Screw the Zipato Bulb 2 into the socket
2. Activate inclusion mode on your Z-Wave controller
3. Turn ON your wall switch
4. Inclusion process will be started automatically


On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.


– Toggle the wall-switch, from OFF, then to ON.
– The bulb will flash once when it has been included into the network


– Toggle the wall-switch, from OFF, then to ON.
– The bulb will flash once and then dim to 5% when it has been excluded outside the network. If you want the bulb to be reincluded, you need re-power the bulb, and then execute the inclusion process.

Product Usage

Zipato does not recommended the use of a line voltage dimmer with bulbs. The reason is that each bulb contains a radio and by reducing or removing power through a line voltage dimmer may cause the connected bulb to not function properly.
For dimming, Zipato recommends using a compatible Z-Wave controller and assoicated application (i.e., Zipato?s Android or iOS application) or a compatible wireless switch that uses the same wireless protocol as the bulb.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, …). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 … 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: Bulb temperature

Read only 
Size: 1 Byte, Default Value:

1 – 100Value

Parameter 255: Factory default

Size: 4 Byte, Default Value: 1

2290649224Factory default

Technical Data

Hardware PlatformZM5202
IP ClassIP 20
Device TypeBulb
Firmware Version02.00
Z-Wave Version04.26
Z-Wave Product Id0x0131.0x0002.0x0003

Supported Command Classes

  • Basic
  • Switch Multilevel
  • Switch All
  • Switch Color
  • Association Grp Info
  • Device Reset Locally
  • Zwaveplus Info
  • Configuration
  • Manufacturer Specific
  • Powerlevel
  • Firmware Update Md
  • Association
  • Version
  • Security

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.
Z-Wave ControllerController VersieCompatibility statusCommentaar
GP-AEOHUBV3EUVolledig compatible
FIB_HOMEC24.130Volledig compatible
FIB_HOMEC24.120Gedeeltelijk compatiblegeen kleur selectie, alleen via LUA, geen association mogelijk
FIB_HOMEC24.600Volledig compatible
ATHEHOMEY02PROVolledig compatible
ZMEERAZ2.3.4Gedeeltelijk compatiblegeen blauwe kleur, geen multicolor element generated
ZMEERAZ2.3.8-rc3Volledig compatible
ZMEERAZ2.3.6Volledig compatible
ZMEERAZ2.3.4Volledig compatible
ZMEEUZBWAY2.3.4Gedeeltelijk compatiblegeen blauwe kleur, geen multicolor element generated
ZMEEUZBWAY2.3.8-rc3Volledig compatible
ZMEEUZBWAY2.3.6Volledig compatible
ZMEEUZBWAY2.3.4Volledig compatible
MCV_VERA_EDGE1.7.3532Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCV_VERA_EDGE1.7.3015Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCV_VERA_EDGE1.7.2236Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_PLUS1.7.3015Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_PLUS1.7.2236Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_PLUS1.7.3532Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_SECURE1.7.3532Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_SECURE1.7.3015Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
MCVEVERA_SECURE1.7.2236Gedeeltelijk compatiblegeen kleur selectie, association niet mogelijk
ZMEEUZBWD2.3.6Volledig compatible
ZMEEUZBWD2.3.4Volledig compatible
ZMEEUZBWD2.3.8-rc3Volledig compatible
ZMEEUZBWD2.3.4Gedeeltelijk compatiblegeen blauwe kleur, geen multicolor element generated
ZMEERAZ22.3.6Volledig compatible
ZMEERAZ22.3.4Volledig compatible
ZMEERAZ22.3.4Gedeeltelijk compatiblegeen blauwe kleur, geen multicolor element generated
ZMEERAZ22.3.8-rc3Volledig compatible
ZMEEUZB12.3.6Volledig compatible
ZMEEUZB12.3.4Volledig compatible
ZMEEUZB12.3.4Gedeeltelijk compatiblegeen blauwe kleur, geen multicolor element generated
ZMEEUZB12.3.8-rc3Volledig compatible
HOMEE-00022.14.1Gedeeltelijk compatiblegeen kleur selectie
HOMEE-00022.17.1Volledig compatible
HOMEE-00022.29.2Gedeeltelijk compatiblegeen kleur selectie