Philio Relay Insert 2 x 1.5 KW Z-Wave Plus

44,50

Philio Relay Insert 2 x 1.5 KW Z-Wave Plus

Philio relais insert 2 x 1.5 KW kunt u bestaande elektrische installaties zoals verlichting, ventilatiesystemen en kleppen integreren met het Z-Wave-netwerk

Type PAN06
Ean: 4713698574406

Beschikbaar via nabestelling

Artikelnummer: PAN06 Categorieën: ,

Beschrijving

Philio Relay Insert 2 x 1.5 KW Z-Wave Plus

Met de Philio Relay Insert 2 x 1.5 KW kunt u bestaande elektrische installaties zoals verlichting, ventilatiesystemen en kleppen integreren in een Z-Wave netwerk. Zo kunnen de aangesloten apparaten nog steeds worden bediend met de bestaande wandschakelaar, maar dankzij Z-Wave Plus ook via afstandsbediening, smartphone of sensorgestuurde automatisering.

Dankzij de kalibratietechnologie kan de Philio Relay Insert 2 x 1.5 KW niet alleen worden gebruikt om AC-apparaten AAN en UIT te schakelen, hij werkt ook perfect met veel soorten licht zoals gloeilampen, fluorescentielampen en LED’s. Daarnaast kan de module ook 12V / DC-apparaten schakelen, zoals 12V MR-16-lampen. Door de maximale belasting van 10 A kunt u hiermee ook een klep of een pomp schakelen.

De compacte radiomodule wordt in een wanddoos geplaatst direct achter de normale schakelaar. De schakelaar is niet langer rechtstreeks verbonden met de belastingen, maar fungeert als invoerapparaat voor de PHILIO Relay insert die de belastingen aanstuurt. De schakelaar stuurt alleen een besturingssignaal naar het inzetstuk dat de belastingen dan weer aanstuurt. De oplossing werkt met alle typen schakelaarontwerpen. U kunt een tijdelijke of tuimelschakelaar gebruiken. Het wordt aanbevolen om wanddozen met een minimale diepte van 65 mm te gebruiken. Maar kleinere dozen met slechts 45 mm diepte kunnen ook worden gebruikt als er voldoende ruimte is achter de schakelaar. De beschikbare ruimte is afhankelijk van de grootte van de traditionele schakelaar, de afmetingen van de wallbox en de hoeveelheid extra bekabeling die in deze box is geplaatst.

Kenmerken Philio Relay Insert:

  • Radiomodule voor wandboxinstallatie 2 onafhankelijke relais
  • Max. belasting: 1500 W elk kanaal
  • 10A in totaal
  • 100 ~ 240VAC, 50 / 60Hz
  • draadloze technologie: Z-Wave Plus
Article Dimensions (WxHxL)68 x 83 x 27 mm
Package Dimensions (WxHxL)90 x 61 x 84 mm
Article net weight0.051 Kg
Article gross weight0.095 Kg
Z-Wave Plus
WEEE
CE

Philio Tech
Relay Insert 2 * 1.5 KW
SKU: PHI_PAN06
ZWave+

Quickstart
This is a On/Off Power Switch for Europe. To run this device please connect it to your mains power supply.

Tripple Click the Button on the device confirms the inclusion, exclusion and association. After power up it will stay in auto inclusion mode for 4 minutes. To support handling of the device when already installed the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description
This Insert Switch allows controlling two independent loads both wirelessly via Z-Wave and locally utilizing a traditional wall switch. Thanks to its calibration technology the device cannot only be used to switch resistive devices but also works perfectly with many kind of reactive or resistive loads such as fluorescent lights or LEDs. The device is placed in a wall box right behind the normal switch. The switch is not longer directly connected to the load but acts as input device for the insert that is controlling the load. This device is designed for a 3 wire system and needs a neutral wire in the wall box.

Prepare for Installation / Reset
Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Tripple Click the button on the device to enter inclusion mode. Within 1 second press the button again for 5 seconds until LED is off.

Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Put the in wall switch into a wall box and connect the pins as shown in the figure.

Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion
Tripple Click the button on the device confirms inclusion. After power up it will stay in auto inclusion mode for 4 minutes. To support handling of the device when already installed the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Exclusion
Tripple Click the button on the device confirms exclusion.

Product Usage
Manual Operation

The device can be operated using the externally connected switch. Three different modes are supported:

Edge Mode: Die Position of the external switch determines the switching state of the relay. After a wireless switching command it may be needed to operate the switch twice to return to the direct relation of switch position and relay state. This mode is the factory default mode.
Toogle Mode: Each “ON”-Position of the external switch will toggle the state of the relays. This mode is particularly suited for mono-stable switches.
Edge/Toggle-Mode: Every change of the state of the external switch results in a change of the relay state.
Remote Operation

Remote On/Off control of the switch is possible with any Z-Wave controller. Further you can set associations to let your device controlled by other Z-Wave devices like sensors.

Node Information Frame
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Tripple Click the button on the device sends out a Node Information Frame.

Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, …). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:
Group Number Maximum Nodes Description
1 1 The Switch will report ON/OFF status of Relay1 and Relay2
2 1 The Switch will report ON/OFF status of Relay1
3 1 The Switch will report ON/OFF status of Relay2
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 … 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: Slected Relay
If Controller not using Multi_Channel command class to access the relay of PAN06, you may configure the select value to react the Basic Command Class or Binary Switch Command Class.
Size: 1 Byte, Default Value: 3

Setting Description
1 Relay 1
2 Relay 2
3 Relay 1 und Relay 2
Parameter 2: Edge or Pulse mode or Edge-Toggle mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle mode.
Size: 1 Byte, Default Value: 1

Setting Description
1 Edge Mode
2 Pulse Mode
3 Edge/Toggle Mode
Parameter 3: Restore switch state mode
Whenever the AC power return from lost, PAN06 will restore the switch state which could be SWITCH OFF、LAST SWITCH STATE、SWITCH ON.
Size: 1 Byte, Default Value: 1

Setting Description
0 Switch off
1 Last switch state
2 Switch on
Parameter 4: Auto off timer
Whenever PAN06 switches to on, the auto off timer begin to count down. After the timer decrease to zero, it will switch to off automatically. However if Auto off timer is set as 0, the auto off function will be disabled.
Size: 2 Byte, Default Value: 0

Setting Description
0 Disable
1 – 32767 Seconds
Parameter 5: RF off command mode
Whenever a switch off command, BASIC_SET, BINARY_SWITCH_SET, SWITCH_ALL_OFF, is received, it could be interpreted as 4 variety of commands.
Size: 1 Byte, Default Value: 0

Setting Description
0 Switch off
1 ignore
2 Switch toggle
3 Switch on
Parameter 6: Existence of Endpoint3
The endpoint3 of Multi-Channel Command Class is related to relay1 and relay2. It may be redundant for the need to control relay1 or relay2 individually. When the Existence of Endpoint3 is set as 0, the endpoint3 of Multi-Channel Command Class will be disabled.
Size: 1 Byte, Default Value: 1

Setting Description
1 Endpoint3 exist
2 No Endpoint3
Technical Data
Dimensions 0.0470000×0.0390000×0.0160000 mm
Weight 40 gr
Hardware Platform SD3502
EAN 4713698571160
IP Class IP 20
Voltage 230 Der Endpunkt3 der Mehrkanal-Befehlsklasse bezieht sich auf Relais1 und Relais2. Es kann überflüssig sein, die Notwendigkeit, Relais1 oder Relais2 einzeln zu steuern. Wenn die Existenz von Endpunkt3 als 0 gesetzt ist, wird der Endpunkt3 der Mehrkanal-Befehlsklasse deaktiviert.
Load 2x 1500W
Device Type On/Off Power Switch
Generic Device Class Binary Switch
Specific Device Class Binary Power Switch
Firmware Version 01.08
Z-Wave Version 03.5f
Certification ID ZC10-14120009
Z-Wave Product Id 0x013c.0x0001.0x0013
Frequency Europe – 868,4 Mhz
Maximum transmission power 5 mW
Supported Command Classes
Basic
Switch Binary
Switch All
Scene Activation
Scene Actuator Conf
Association Grp Info
Device Reset Locally
Zwaveplus Info
Multi Channel
Configuration
Alarm
Manufacturer Specific
Powerlevel
Protection
Firmware Update Md
Association
Version
Explanation of Z-Wave specific terms
Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.

Z-Wave ControllerController RevisionCompatibility statusCommentaar
FIB_HOMEC24.180Volledig compatiblemultiple switches created
FIB_HOMEC24.130Volledig compatible
FIB_HOMEC24.450Volledig compatibleMust be set associations
POPEHOME40.126Volledig compatible
ZMEERAZ2.3.8Volledig compatible
ZMEERAZ2.3.8-rc3Volledig compatible
ZMEERAZ2.3.4Volledig compatible
ZMEEUZBWAY2.3.8-rc3Volledig compatible
ZMEEUZBWAY2.3.4Volledig compatible
ZMEEUZBWAY2.3.8Volledig compatible
MCVEVERA_PLUS1.7.4453Volledig compatible
MCVEVERA_PLUS1.7.3015Volledig compatible
MCVEVERA_PLUS1.7.4001Volledig compatiblemultiple switches created
ZMEEUZBWD2.3.8-rc3Volledig compatible
ZMEEUZBWD2.3.4Volledig compatible
ZMEEUZBWD2.3.8Volledig compatible
ZMEERAZ22.3.4Volledig compatible
ZMEERAZ22.3.8Volledig compatible
ZMEERAZ22.3.8-rc3Volledig compatible
ZMEEUZB12.3.4Volledig compatible
ZMEEUZB12.3.8-rc3Volledig compatible
ZMEEUZB12.3.8Volledig compatible